Dead Weight Testers | Master Test Gauges | Pressure Calibrators | Temperature Calibrators | Multifunction Calibrators | Electrical Test Equipment | Decade Boxes | Pressure Gauges | Instrument Valves | DBB & Monoflanges | Mixers

Budenberg Middle East Trading LLC,  Office no. 217  Bil Obaida Building,  Al Nahda Road,  Al Qusais 1,  Dubai,  United Arab Emirates

time electronics pressure calibrators

What we offer?

Budenberg Middle East offers Time Electronics portable pressure calibrators for Gauge Pressure and Differential Pressure calibration from vacuum….200 mbar up to 600 bar field pressures for field and Calibration laboratory. 

The calibrators are supplied with Traceable Calibration and UKAS Calibration, if ordered separately.

The 7010 is a fully integrated pressure test and calibration system. It is suitable for field and laboratory calibration work of both pressure and electrical process loop signals. The instrument has a single pressure channel with the range specified on ordering. Standard available versions are; 0.2, 2, 5, 10, 20, 35, 70, 100, 200, 400, and 600 bar. Vacuum down to -850 mbar is possible on the 2 bar version. Other ranges are available upon request.

For process signal calibration the loop signal is displayed on the LCD display to 0.05% accuracy. Loop drive supply (24V or 36V) is also provided. Both pressure and loop signal can be displayed at the same time to speed up the calibration of pressure transmitters. Additionally a continuity function is available for testing for open circuit loops.

Both pressure and loop current are displayed on separate 4.5 digit LCD displays.

The 7010 allows switch selection of five pressure units. These must be specified on ordering from the following:- bar, PSI, kPa, MPa, inWg, cmWg, inHg, mmHg, Kg/cm2, atm.

For the 7010, input pressure can be generated by external hand pumps, 7090 pneumatic (-950 mbar to 40 bar), or 7095 hydraulic (0 to 700 bar).

The 7010 is housed in an impact resistant safety case that provides protection and increased durability. All pressure connections are on the side of the case.

The instrument is supplied with a pressure hose, electrical test lead, 2 electrical probes and 2 crocodile clips. The other features include:

  • Vacuum to 600bar versions available
  • Accuracy 0.04% of full scale
  • Pneumatic or hydraulic
  • Up to 5 selectable engineering units
  • Loop current measure
  • 24/36V loop power
  • Over-pressure alarm
  • RS-232 serial interface
  • EasyCal software compatible
  • Mains or battery powered
Click to enlarge

The 7015 is a fully integrated pressure test and calibration system. It is suitable for field and laboratory calibration work of both pressure and electrical process loop signals. The instrument has two pressure channels with the ranges specified on ordering. Standard available ranges for each channel are; 0.2, 2, 5, 10, 20, 35, 70, 100, 200, 400, and 600 bar. Vacuum down to -850 mbar is possible on the 2 bar version. Other ranges are available upon request.

For process signal calibration the loop signal is displayed on the LCD display to 0.05% accuracy. Loop drive supply (24V or 36V) is also provided. Both pressure and loop signal can be displayed at the same time to speed up the calibration of pressure transmitters. Additionally a continuity function is available for testing for open circuit loops.

Both pressure and loop current are displayed on separate 4.5 digit LCD displays.

The 7015 allows switch selection of five pressure units. These must be specified on ordering from the following:- bar, PSI, kPa, MPa, inWg, cmWg, inHg, mmHg, Kg/cm2, atm.

For the 7015, input pressure can be generated by external hand pumps, 7090 pneumatic (-950 mbar to 40 bar), or 7095 hydraulic (0 to 700 bar).

The 7015 is housed in an impact resistant safety case that provides protection and increased durability. All pressure connections are on the side of the case.

The instrument is supplied with a pressure hose, electrical test lead, 2 electrical probes and 2 crocodile clips. The other features include:

  • Vacuum to 600bar versions available
  • Accuracy 0.04% of full scale
  • Pneumatic or hydraulic
  • Dual channel – 4 & 5 engineering units
  • Loop current measure
  • 24/36V loop power
  • Over-pressure alarm
  • RS232 serial interface
  • EasyCal software compatible
  • Mains or battery powered
Click to enlarge

The 7016 is a fully integrated pressure test and calibration system. It is suitable for field and laboratory calibration work of both regulated low pressure and electrical process loop signals. The instrument is available in pressure or vacuum regulated configuration, with the range specified on ordering. Standard available versions are; Vacuum, 0.2, 2, 5, 10, or 20 bar. Other ranges are available upon request.

For process signal calibration the loop signal is displayed on the LCD display to 0.05% accuracy. Loop drive supply (24V or 36V) is also provided. Both pressure and loop signal can be displayed at the same time to speed up the calibration of pressure transmitters. Additionally a continuity function is available for testing for open circuit loops.

Both pressure and loop current are displayed on separate 4.5 digit LCD displays.

The 7016 allows switch selection of five pressure units. These must be specified on ordering from the following:- bar, PSI, kPa, MPa, inWg, cmWg, inHg, mmHg, Kg/cm2, atm.

For the 7016, input pressure can be generated by the 7090 pneumatic hand pump (-950 mbar to 40 bar).

The 7016 is housed in an impact resistant safety case that provides protection and increased durability. All pressure connections are on the side of the case.

The instrument is supplied with a pressure hose, electrical test lead, 2 electrical probes and 2 crocodile clips. The other features include:

  • Vacuum to 20bar versions available
  • Accuracy 0.04% of full scale
  • Pneumatic
  • Up to 5 selectable engineering units
  • Loop current measure
  • 24/36V loop power
  • Over-pressure alarm
  • RS232 serial interface
  • EasyCal software compatible
  • Mains or battery powered
Click to enlarge

The 7018 is a fully integrated differential pressure test and calibration system. It is suitable for field and laboratory calibration work of both differential pressure and electrical process loop signals. The instrument is available in pressure or vacuum configuration, with the range specified on ordering. Standard available versions are; Vacuum 0.2, 2, 5, or 10 bar. Static line pressures must also be specified.

For process signal calibration the loop signal is displayed on the LCD display to 0.05% accuracy. Loop drive supply (24V or 36V) is also provided. Both pressure and loop signal can be displayed at the same time to speed up the calibration of pressure transmitters. Additionally a continuity function is available for testing for open circuit loops.

Both pressure and loop current are displayed on separate 4.5 digit LCD displays.

The 7018 allows switch selection of five pressure units. These must be specified on ordering from the following:- bar, PSI, kPa, MPa, inWg, cmWg, inHg, mmHg, Kg/cm2, atm.

For the 7018, input pressure can be generated by the 7090 pneumatic hand pump (-950mbar to 40bar).

The 7018 is housed in an impact resistant safety case that provides protection and increased durability. All pressure connections are on the side of the case.

The instrument is supplied with a pressure hose, electrical test lead, 2 electrical probes and 2 crocodile clips. The other features include:

  • Vacuum to 10bar versions available
  • Accuracy 0.04% of full scale
  • Pneumatic
  • Up to 5 selectable engineering units
  • Loop current measure
  • 24/36V loop power
  • Over-pressure alarm
  • RS232 serial interface
  • EasyCal software compatible
  • Mains or battery powered
Click to enlarge